Channel Master 9537EU Istruzioni per gli Interventi Scaricare il pdf

Programmable Antenna Rotator Controller

with Infra-Red Remote Control

Owner’s Guide to Installation and Use

Model 9521 Drive and Controller, 117 VAC

Model 9521EU Drive and Controller, 230 VAC

Model 9537 Controller Only, 117 VAC

Model 9537EU Controller Only, 230 VAC

CAUTION: Read and adhere to all IMPORTANT SAFEGUARDS listed elsewhere in this book-

let. Read and observe safety, installation and operating instructions supplied with this

unit and with your antenna BEFORE installation or operation. Retain this booklet and all

instructions for your safety and future reference.

Controller Compatibility - If purchased separately, the Model 9537 controller may be used with the

following rotator drive units:

Channel Master

- Models 9500, 9510(A), 9512, 9513, 9515(A)

Radio Shack

- Model 15-1225

If you are upgrading an existing installation with Model 9537 controller, skip to “Model 9537 Programmable

Controller” in this leaflet.

Drive Unit Installation

STEP 1 – Determine proper size number of rotator cable from chart. Three conductor cable is

suitable, but if four conductor cable is used, connect both conductors 3 and 4 to terminal 3 of the

terminal board.

Gage No. of Maximum Length

AWG MM Conductors Feet Meters

22 0,6 3 180 55

22 0,6 4* 200 61

20 0,8 3 280 85

20 0,8 4* 310 95

18 1,0 3 445 136

18 1,0 4* 510 155

*Attach 3 and 4 conductors to No. 3 terminals on control and drive.

STEP 2 – Install drive unit. On new drive units, arrow on mast support should be aligned with arrow shaped

mast stop on housing. Install antenna pointing south. When desired channels are close to or on oppo-

site sides of the north end stops, the antenna may be installed pointing north. Note, however, that the

antenna will then be pointing in the opposite direction from that indicated on the control.

An alternative means of setting up is to perform a synchronization of the drive unit using the controller.

Then set up the antenna pointing north. Ensure power is disconnected from the controller when

making antenna adjustments.

1 2 3 4 5 6 7 8 9 10

Sommario

Pagina 1 - Drive Unit Installation

Programmable Antenna Rotator Controllerwith Infra-Red Remote ControlOwner’s Guide to Installation and UseModel 9521 Drive and Controller, 117 VACModel

Pagina 2 - Terminal Connections

Model 9537 Controller Only: Channel Mastr®1315 Industrial Park Drive, Smithfield, NC 27577, USAModel 9521 Drive and Controller/ Channel Master®Rotator

Pagina 3 - Model 9537

Black Wireto #2Red Wireto #3Green Wire to #1CoverTerminalsGrommetDrive UnitGrommetTerminal ConnectionsStandard Mast MountingUsing 9523 Alignment Beari

Pagina 4

Features:• 69 Programmable Antenna Locations (01-69) - Allows location number to be sameas channel number.• Digital Compass 000-360 degrees with direc

Pagina 5

Controller Installation and SetupImportant Note! Before disconnecting old control box, make noteof each wire color and the corresponding terminal conn

Pagina 6

Operation From The Supplied Handheld Remote1. Install 2 AAA batteries in the handheld remote.2. Check operation by pressing the POWER button and obser

Pagina 7 - IMPORTANT SAFEGUARDS

8. SynchronizationPress the SYNC key on the front panel or 00 DOWN from the handheld. A counterclockwise move-ment is performed to synchronize the con

Pagina 8

IMPORTANT SAFEGUARDSYour antenna rotator unit, consisting of a control and a drive, has been engineered and manufacturedto assure your personal safety

Pagina 9

8. All individuals, especially children, should be cautioned about dropping or pushing objects into anyopenings. Some internal parts carry hazardous v

Pagina 10 - (17147) Rev. A

Appendix B Handheld Remote Control Command SummarySYNC: 00▼PROGRAM: #▲# (# = 01-69)DISPLAY MEMORIES/STATUS: 99▲AUTOSYNC ON/RESET TO 50: 98▲AUTOSYNC O